How To String A Weed Eater With One Hole?

  1. While you are loading the spool, push about half an inch of one end of the string into the hole.
  2. This will cause the hole to retain the string in place while you load the spool.
  3. If your weed eater utilizes two strings, the spool you use should have two pieces that are divided by a separator, and each portion should have a hole in it.
  4. Winding weed eaters with two strings requires doing so one piece of string at a time.

How to string a dual sided Weed Eater spool?

  1. Step-by-step instructions on how to string a dual-sided weed eater spool.
  2. You should wind the lines onto the spool, but you should leave approximately a foot and a half of the lines unwound.
  3. Slide the spool back into the cover after passing the line ends, one at a time, through the exit holes, and then push the line ends through the cover.
  4. Check that the lines have room to move freely.
  5. Place the cover over the cutting head of the weed eater, then snap it back into place.

How to wind a weed eater string?

Following the arrow direction that is printed on the spool is the fundamental premise of wrapping weed eater string onto the spool. Simply wind it in the opposite direction of the cutting head if the spool does not include any arrows indicating the way to wind it in anyplace on it. #3: What is the proper way to replace the string on the weed eater?

How to use a weed eater with lines?

  1. You should wind the lines onto the spool, but you should leave approximately a foot and a half of the lines unwound.
  2. Slide the spool back into the cover after passing the line ends, one at a time, through the exit holes, and then push the line ends through the cover.
  3. Check that the lines have room to move freely.
  4. Place the cover over the cutting head of the weed eater, then snap it back into place.
See also:  How To Fix Dry Weed?

What size line do you put on a craftsman Weed Eater?

The weed eater model number 358.791590 from Craftsman features a dual-sided spool that can accommodate 0.095-inch line and must be loaded into the spool in the same way each time. Buying a pre-wound spool of line will make it much quicker for you to replace the line on your trimmer. Because of this, having to wound line onto the spool is no longer necessary.

How do you restring an electric weed eater with one hole?

Set up the string for the trimmer. Insert a portion of the trimmer line measuring roughly half an inch from one end into one of the holes located on the upper section of the spool. The next step is to carefully wind the string around the spool in the direction shown by the arrows on the spool, being sure to leave about 4 inches of the string exposed.

How do you string a weed eater without taking it apart?

  1. To restring a weedeater, you need only thread the wire through the head of the tool, and then thread it through the eyelets of the handle.
  2. After that, you should put it back together while leaving all of the wiring exposed.
  3. What is this, exactly?
  4. The ideal winding may be achieved by only holding the upper side of the head and turning the lower side of the head in the opposite direction.
  5. This completes the process.

Do you soak weed eater string in water?

You should never keep your string exposed to direct sunlight, and you should soak your string in water at some point throughout the summer months in particular. Because of this, soaking your string in water will prevent the string from deteriorating from the heat, and it will also maintain your string in prime condition for weed-whacking!

See also:  How Much For A Lb Of Weed?

What makes a weed eater hard to pull?

It is possible for the pull rope of a weed eater to get too taut to be pulled, which makes it difficult or even impossible to start the machine. If this problem develops, the rope will either become twisted or become caught on the rope rotor, which will prohibit it from moving without an excessive amount of effort being used.

What causes a weed eater to lock up?

  1. Broken Clutch The majority of string trimmers come equipped with a centrifugal clutch, which prevents the drive shaft from interacting with the engine flywheel until the string trimmer has been started and the throttle lever has been depressed.
  2. However, if the clutch springs are damaged, the clutch won’t disengage and the drive shaft will revolve when you pull the starter rope.
  3. This is because the broken springs prevent the clutch from being compressed.

What size string does a Craftsman weed eater use?

Trimmer line for Craftsman trimmers, string for weed eaters 0.065, trimmer line 0.065.

Leave a Reply

Your email address will not be published.

Adblock
detector