How can I increase the length of my Stihl trimmer’s line? Remove the spool cap and unwind some new line from the spool to expand the line on your Stihl trimmer. Cut the line to the required length, then attach one end to the spool. Wind the line in the direction of the arrow around the spool. Replace and tightly tighten the spool cap.
Why purchase a Black & Decker grass trimmer?
Auto-Feed Not Working on Your Black & Decker Trimmer – The Black and Decker Trimmer automatically feeds out additional line using a spring and a bump spool. When the head is tapped on the ground, the line is released. However, occasionally the head might become clogged with sap or debris, rendering the trimmer inoperable.
Can the string and spool of a Black & Decker Trimmer be replaced?
Article Download Article Download Black & Decker trimmers are valuable gardening equipment that may be used to remove weeds and trim bushes. However, with time, your line may become worn or damaged, rendering your trimmer ineffective. If you follow the necessary steps, you may change the string and spool on your trimmer without difficulty.
- WH.performance.mark(‘image1_rendered’)
- ” data-src=”https://www.wikihow.com/images/thumb/a/ab/Replace-the-Line-on-a-Black-and-Decker-Trimmer-Step-1-Version-5.jpg/v4-460px-Replace-the-Line-on-a-Black-and-Decker-Trimmer-Step-1-Version-5.jpg” src=”https://www.wikihow.com/images/thumb/a/ab/Replace-the-Line-on-a-Black-and-Decker-Trimmer-Step-1-Version-5.jpg/v4-460px-Replace-the-Line-on-a-Black-and-Decker-Trimmer-Step-1-Version-5.jpg”>
- 1 Turn off the trimmer’s power source. In order to securely replace the line on your power trimmer, it is crucial that it does not switch on while you are working on it. Unplug the trimmer or remove the included ion battery. This will prevent you from accidently activating the trimmer and sustaining an injury.
- 2 Place the trimmer on a chair or table. Set your Black & Decker trimmer on a table or chair so you can operate with it without continually bending down. Choose a table or workstation that reaches your waist so that you may replace its components with ease. Advertisement
- 3 Remove the trimmer head’s cap. On your Black and Decker trimmer, there will be a cap that covers the line. To remove this, press in the tabs on both sides of the cap with your fingers. After depressing the tabs, simply push up on the trimmer cap to remove it and expose the spool beneath.
- 4 Remove the lid from the spool. Flip the cover over to see the line and spool. On the side of your cap will be two indentations or eyelets that keep the line in place. Remove the line from the cap’s perforations, then grasp the spool and slowly wriggle it free of the cap.
- 5 Eliminate the previous line from the spool. To remove the old line, take it from the eyelets that are holding it in place and pull the end of the line that is not attached. This will result in the old string being removed. Repeat the procedure on the opposite side of the spool to eliminate any old lines.
Wear gloves when operating a trimmer. Advertisement 1 Insert the fresh line into the corresponding holes on the spool. Purchase a round monofilament line with a.080 inch (2.0 mm) diameter from a hardware shop. Because heavier or serrated line might overload the motor and cause it to overheat, it should not be used. Additionally, you may purchase pre-threaded spools from Black & Decker’s website and at various hardware stores. 2 Following the directions on the spool, wind the line around the spool. Introduce the line through the hole and start to wind it around the spool. The greater the overlap of your spool, the more likely it may become tangled when you begin using it. Instead, wrap the spool such that the line is wrapped beside itself, as opposed to over itself.
- 3 Cut the line and secure it to the spool. After looping your line around the spool, provide 6 inches (15.24 cm) of slack. Cut the thread with gardening shears or sharp scissors, then thread the extra line through the eyelets on the spool to secure it.
- 4 Wind and thread the other side of the spool. Repeat the procedures to secure and wound the second line onto the spool. Follow the directions once again as you wind up the line.
- Advertisement
- 1 Place the spool into the cap. Also ensure that the eyelets on the cap and spool are aligned. Align the hole in the center of the spool with the hole in the center of the cap and push the spool gently back into the cap. Once you hear a click, flip the top over and shake it to ensure the spool is securely in place.
- 2 Lace the line through the cap’s eyelets. Pull the surplus line from the spool’s eyelets and insert it into the cap’s eyelets. Your spool is now prepared for reinstallation into your trimmer.
- 3 Align the tabs on the trimmer head and cap and press down. To insert your cap into the trimmer head, depress the cap’s side tabs. Press the cap lightly until you hear a click. Your spool has been changed.
- Advertisement
Add fresh query
- Question How does the string feed itself? Previously, pounding the spool on the ground worked, but not with this Black & Decker trimmer. What should I do? Determine whether it is an automated or bump feeder. Your previous trimmer was a bump feeder, so you did the correct thing while attempting to feed the string, but doing so on a device with an automated feeder might cause harm. Read the packaging and directions. If the feed is automated, you do not need to do anything
- it will adjust itself. If you have already struck it and it still does not function, you may have destroyed the feed motor.
- Question I own a B&D 20 V battery-powered lawn mower and edger. When should a fresh string be obtained? If you do not have a spare line, purchase one immediately. Thus, you will have it when you need it. When there is no more of the previous line, you replace it.
- Question Should the line be wound onto the spool in the same direction as it rotates during operation? Follow the arrows on the side of the spool when winding it for optimal results. Typically, the direction is anti-clockwise.
See more answers Submit a Question left 200 characters Include your your address to receive a notification once this question has been answered. Submit Advertisement
How does the Black & Decker Trimmer trim long grass?
Auto-Feed Not Working on Your Black & Decker Trimmer – The Black and Decker Trimmer automatically feeds out additional line using a spring and a bump spool. When the head is tapped on the ground, the line is released. However, occasionally the head might become clogged with sap or debris, rendering the trimmer inoperable.