How To Wind A Craftsman Weed Eater Spool?

How To Wind A Craftsman Weed Eater Spool
Step 7: Screwing the retainer ring back into the head of the trimmer: – In the final step, the retaining ring must be reattached to the trimmer snap in the correct position. Specifically, if you are using a two-string weed eater, this step is the most relevant.

Why does my trimmer line keep jamming?

Why does the line on my weed eater often become clogged? As with trimmers from other manufacturers, many Weed Eater trimmers have a head that automatically moves the line or string that cuts weeds and grass. Other versions from Poulan Pro, the manufacturer of the Weed Eater brand, include a bump-and-feed function that advances the line when the head is bumped on the ground.

The culprit of your Weed Eater’s inability to advance the line might be the line you’re using, the way you loaded it, or your bumping method. There is a maximum line diameter that may be utilized in a Weed Eater trimmer head or any other trimmer head. There are several varieties of trimmer line, including serrated line and line with a non-circular cross-section.

You may take advantage of the greater cutting power of these various types of line as long as you do not exceed the trimmer head’s line diameter range. If the line is too large for the head, it will not progress. Check the operator’s handbook or the Weed Eater website to determine the correct line diameter for your model.

  • Some trimmer heads take two lengths of line, each of which is secured to a different hole on the spool hub.
  • Typically, the technique for winding the two lengths of line entails keeping them together and winding them simultaneously, while preventing one line from crossing over itself or the other.
  • At such a cross-over point, the line will be fixed.
See also:  What Happens If You Get Caught With Weed Under 18 In Michigan?

Regardless of whether your Weed Eater trimmer requires one or two lengths of line, wound the line in the direction indicated by the arrow on the spool. A line will not advance if it is coiled in the other way. If the head of your Weed Eater trimmer is bump-and-feed, the line will not progress automatically, as it would with an automatic-feed type.

  • Tap the head periodically on the ground to move the line.
  • It is essential, however, that the head spins at full speed when it is struck, as the string is advanced by the centrifugal force of the spinning.
  • Tap the trimmer head only on a soft surface, such as grass, and never on a hard surface, such as concrete or wood, otherwise you risk damaging the head.

It is preferable to knock the head frequently rather than seldom. A guard-mounted blade automatically trims the line to the correct length. If the line of a Weed Eater trimmer head is too short, it will not advance because insufficient centrifugal force acts on it.

  1. This can occur if the head is not tapped frequently enough or if the line is severed by a piece of wire or a root.
  2. Using a trimmer with a line that is 50 percent or less of the specified length might cause the head to rotate too rapidly, causing engine wear.
  3. A broken spring may also be responsible for the line’s inability to proceed.

Depending on the Weed Eater trimmer model, the spring can be replaced by removing the spool from the head or the head from the drive shaft. Why does the line on my weed eater often become clogged?

See also:  When Will Georgia Legalize Weed?

How does a trimmer head with a fixed line operate?

Individual lengths of line are fed or threaded into the trimmer as needed with a fixed head arrangement. This eliminates some of the headaches associated with winding line onto trimmer heads and simplifies the entire process of dealing with trimmer line.

The operation of a bump feed trimmer.

Bump feed electric weed eaters – When the head of a bump feed weed eater is pressed against a flat surface, a spring in the head of the string trimmer is compressed. This movement releases string from the spool, allowing you to chop down trash using a line. The bump feed electric trimmer pulls the string off the spool using centrifugal force.